B1A68
B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 65
- When Monitored:
Anytime the Key is placed in the ignition.
- Set Condition:
This code is set immediately when the Wireless Ignition Node detects the (F892) Ignition Switch Output circuit shorted to ground when the
ignition key is removed.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 66
1. VERIFY THAT DTC B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW
1. With the scan tool, record and erase WIN DTCs.
2. Insert and remove the key from the ignition switch several times.
3. With the scan tool, read the active DTCs.
Does the scan tool display: B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW as active?
Yes
- Go To 2
No
- Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check
all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and poor pin fit.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
2. STEERING COLUMN LOCK MODULE
1. Turn the ignition off.
2. Disconnect the Steering Column Lock Module connector.
NOTE: Check connectors - Clean and repair as necessary.
3. Turn the ignition on.
4. With the scan tool, erase the DTCs.
5. Cycle the ignition switch from On to Off three times.
6. Remove and insert the key in the ignition switch several times.
7. Turn the ignition on.
8. With the scan tool, read the active DTCs.
Does the scan tool display: B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW as active?
Yes
- Go To 3
No
- Replace the Steering Column Lock Module. The Wireless Ignition Node (WIN) must also be replaced along with the Steering Column
Lock Module (ELV). When replacing the WIN and the Steering Column Lock Module (ELV), the WIN MUST be programmed
BEFORE the Steering Column Lock Module (ELV) is programmed..
- Replace and program the Wireless Ignition Node (WIN). See: Powertrain Management/Ignition System/Sensors and Switches - Ignition
System/Ignition Switch/Service and Repair/Wireless Ignition Node Receiver - Removal.
- Replace and program the Steering Column Lock Module (ELV). See: Steering and Suspension/Steering/Steering Column/Steering Column
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 67
Lock/Service and Repair/Shaft Lock Module - Removal.
- Perform the WIN VERIFICATION TEST. See: Verification Tests/Vehicle Theft Security Verification Tests/Wireless Ignition Node (WIN)
Verification Test.
3. CHECK THE (F892) IGNITION SWITCH OUTPUT (KEY-IN) CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the Wireless Ignition Node harness connector.
3. Measure the resistance between ground and the (F892) Ignition Switch Output (Key-In) circuit in the Steering Column Lock harness
connector.
Is the resistance below 10,000 Ohms?
Yes
- Repair the (F892) Ignition Switch Output (Key-In) circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
- Replace the Wireless Ignition Node (WIN). The Steering Column Lock Module must also be replaced along with the WIN. When
replacing the WIN and the Steering Column Lock Module (ELV), the Win MUST be programmed BEFORE the Steering Column
Lock Module (ELV) is programmed. .
- Replace and program the Wireless Ignition Node (WIN). See: Powertrain Management/Ignition System/Sensors and Switches - Ignition
System/Ignition Switch/Service and Repair/Wireless Ignition Node Receiver - Removal.
- Replace and program the Steering Column Lock Module (ELV). See: Steering and Suspension/Steering/Steering Column/Steering Column
Lock/Service and Repair/Shaft Lock Module - Removal.
- Perform the WIN VERIFICATION TEST. See: Verification Tests/Vehicle Theft Security Verification Tests/Wireless Ignition Node (WIN)
Verification Test.
B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 65
- When Monitored:
Anytime the Key is placed in the ignition.
- Set Condition:
This code is set immediately when the Wireless Ignition Node detects the (F892) Ignition Switch Output circuit shorted to ground when the
ignition key is removed.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 66
1. VERIFY THAT DTC B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW
1. With the scan tool, record and erase WIN DTCs.
2. Insert and remove the key from the ignition switch several times.
3. With the scan tool, read the active DTCs.
Does the scan tool display: B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW as active?
Yes
- Go To 2
No
- Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check
all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and poor pin fit.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
2. STEERING COLUMN LOCK MODULE
1. Turn the ignition off.
2. Disconnect the Steering Column Lock Module connector.
NOTE: Check connectors - Clean and repair as necessary.
3. Turn the ignition on.
4. With the scan tool, erase the DTCs.
5. Cycle the ignition switch from On to Off three times.
6. Remove and insert the key in the ignition switch several times.
7. Turn the ignition on.
8. With the scan tool, read the active DTCs.
Does the scan tool display: B1A68-STEERING COLUMN LOCK MODULE BOLT CONTROL LOW as active?
Yes
- Go To 3
No
- Replace the Steering Column Lock Module. The Wireless Ignition Node (WIN) must also be replaced along with the Steering Column
Lock Module (ELV). When replacing the WIN and the Steering Column Lock Module (ELV), the WIN MUST be programmed
BEFORE the Steering Column Lock Module (ELV) is programmed..
- Replace and program the Wireless Ignition Node (WIN). See: Powertrain Management/Ignition System/Sensors and Switches - Ignition
System/Ignition Switch/Service and Repair/Wireless Ignition Node Receiver - Removal.
- Replace and program the Steering Column Lock Module (ELV). See: Steering and Suspension/Steering/Steering Column/Steering Column
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 67
Lock/Service and Repair/Shaft Lock Module - Removal.
- Perform the WIN VERIFICATION TEST. See: Verification Tests/Vehicle Theft Security Verification Tests/Wireless Ignition Node (WIN)
Verification Test.
3. CHECK THE (F892) IGNITION SWITCH OUTPUT (KEY-IN) CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the Wireless Ignition Node harness connector.
3. Measure the resistance between ground and the (F892) Ignition Switch Output (Key-In) circuit in the Steering Column Lock harness
connector.
Is the resistance below 10,000 Ohms?
Yes
- Repair the (F892) Ignition Switch Output (Key-In) circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
- Replace the Wireless Ignition Node (WIN). The Steering Column Lock Module must also be replaced along with the WIN. When
replacing the WIN and the Steering Column Lock Module (ELV), the Win MUST be programmed BEFORE the Steering Column
Lock Module (ELV) is programmed. .
- Replace and program the Wireless Ignition Node (WIN). See: Powertrain Management/Ignition System/Sensors and Switches - Ignition
System/Ignition Switch/Service and Repair/Wireless Ignition Node Receiver - Removal.
- Replace and program the Steering Column Lock Module (ELV). See: Steering and Suspension/Steering/Steering Column/Steering Column
Lock/Service and Repair/Shaft Lock Module - Removal.
- Perform the WIN VERIFICATION TEST. See: Verification Tests/Vehicle Theft Security Verification Tests/Wireless Ignition Node (WIN)
Verification Test.
