B1D7F
B1D7F-SEAT FRONT VERTICAL MOTOR CONTROL CIRCUIT PERFORMANCE
- When Monitored:
Whenever the seat motor is activated.
- Set Condition:
If the Memory Seat Module does not detect the rotation of the seat motor this DTC will set. This DTC will only set when the seat switch is
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 325
moved in the same direction three consecutive times.
1. CHECK FOR RELATED DIAGNOSTIC TROUBLE CODES
1. Turn the ignition on.
2. With the scan tool, read DTC's.
Does the scan tool display any seat position sensor DTC's?
Yes
- Diagnose and repair other DTC(s) first. See: .
No
- Go To 2
2. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, record and erase DTC's
3. Move the Seat Switch in the Front Vertical position three times.
4. With the scan tool, read DTC's.
Does the scan tool display B1D7F-SEAT FRONT VERTICAL MOTOR CONTROL CIRCUIT PERFORMANCE?
Yes
- Go To 3
No
- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and
connectors.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
3. CHECK THE (G404) DRIVER SEAT FRONT VERTICAL POSITION SENSE VOLTAGE
1. Disconnect the Front Driver Vertical Seat Adjuster Motor.
NOTE: Check connectors - Clean and repair as necessary.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 326
2. Move the Seat Switch in the front vertical position during the next step.
3. Using a 12-volt test light connect one lead to the (G404) Driver Seat Front Vertical Position Sense circuit and the other lead to Driver Seat
Front Vertical Sensor Ground at the Driver Front Vertical Seat Adjuster Motor connector.
Does the test light illuminate for approximately two seconds then turn off with the seat switch engaged?
Yes
- Go To 4
No
- Go To 5
4. CHECK THE DRIVER SEAT FRONT VERTICAL UP/DOWN DRIVER VOLTAGE
1. Move the Seat Switch in the front vertical position during the next step.
2. Using a 12-volt test light connect one lead to the (G119) Driver Seat Front Vertical Up Driver circuit and the other lead to (P121) Driver Seat
Front Vertical Down Driver circuit at the Front Driver Vertical Seat Adjuster Motor connector.
Does the test light illuminate with the seat switch engaged?
Yes
- Replace the Front Driver Vertical Seat Adjuster motor assembly.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
No
- Go To 7
5. CHECK THE (G404) DRIVER SEAT FRONT VERTICAL POSITION SENSE WIRE FOR AN OPEN
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 327
1. Disconnect the Memory Seat Module C3 connector.
NOTE: Check connectors - Clean and repair as necessary.
2. Measure the resistance of the (G404) Driver Seat Front Vertical Position Sense circuit at the Front Driver Vertical Seat Adjuster Motor
connector to the C3 connector.
Is the resistance above 1.0 ohm?
Yes
- Repair the (G404) Driver Seat Front Vertical Position Sense circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
No
- Go To 6
6. CHECK THE (G494) DRIVER SEAT FRONT VERTICAL SENSOR GROUND FOR AN OPEN
1. Measure the resistance of the (G494) Driver Seat Front Vertical Sensor Ground circuit at the Driver Front Vertical Seat Adjuster Motor
connector to the C3 connector.
Is the resistance above 1.0 ohm?
Yes
- Repair the (G494) Driver Seat Front Vertical Senor Ground circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
No
- Replace the Memory Seat Module.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 328
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
7. CHECK THE (P119) DRIVER SEAT FRONT VERTICAL UP DRIVER WIRE FOR AN OPEN
1. Disconnect the Memory Seat Module C3 connector.
NOTE: Check connectors - Clean and repair as necessary.
2. Measure the resistance of the (P119) Driver Seat Front Vertical Up Driver circuit at the Driver Front Vertical Seat Adjuster Motor connector
to the C3 connector.
Is the resistance above 1.0 ohm?
Yes
- Repair the (P119) Driver Seat Front Vertical Up Driver circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
No
- Go To 8
8. CHECK THE (P121) DRIVER SEAT FRONT VERTICAL DOWN DRIVER FOR AN OPEN
1. Measure the resistance of the (P121) Driver Seat Front Vertical Down Driver circuit at the Driver Front Vertical Seat Adjuster Motor
connector to the C3 connector.
Is the resistance above 1.0 ohm?
Yes
- Repair the (P121) Driver Seat Front Vertical Down Driver circuit for an open.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 329
No
- Replace the Memory Seat Module.
- Perform POWER SEAT SYSTEM VERIFICATION TEST. See: Verification Tests/Power Seat System Verification Test.
