B1D09
B1D09-DRIVER MIRROR POSITION SENSOR POWER SUPPLY CIRCUIT LOW
- When Monitored:
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 330
Continuously.
- Set Condition:
If the Driver Door Module senses the voltage is less than 4.3 volts for more than 30 ms on the (P669) Driver Mirror Sensor Supply circuit.
1. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, record and erase DTCs.
3. Operate the Mirror Switch in all directions several times.
4. Cycle the ignition from on to off 3 times.
5. Turn the ignition on.
6. With the scan tool, read DTCs.
Does the scan tool display: B1D09-DRIVER MIRROR POSITION SENSOR POWER SUPPLY CIRCUIT LOW?
Yes
- Go To 2
No
- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and
connectors.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
2. TEST FOR A SHORTED OUTSIDE REARVIEW MIRROR
1. Turn the ignition off.
2. Disconnect the Driver Outside Rearview Mirror connector.
3. Turn the ignition on.
4. Measure the voltage between the (P669) Driver Mirror Sensor Supply circuit and the (P69) Driver Mirror Sensor Ground circuit.
Is the voltage above 4.6 volts?
Yes
- Replace the Outside Rearview Mirror.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
- Go To 3
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 331
3. CHECK THE (P669) DRIVER MIRROR SENSOR SUPPLY CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the Driver Door Module C2 connector.
3. Measure the resistance between ground and the (P669) Driver Mirror Sensor Supply circuit in the Driver Door Module C2 connector.
Is the resistance below 10k ohms?
Yes
- Repair the (P669) Driver Mirror Sensor Supply circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
- Go To 4
4. CHECK THE (P669) DRIVER MIRROR SENSOR SUPPLY CIRCUIT FOR A SHORT TO THE (Z911) GROUND CIRCUIT
1. Measure the resistance between the (P669) Driver Mirror Sensor Supply circuit and the (Z911) Ground circuit in the Driver Door Module C2
connector.
Is the resistance below 10k ohms?
Yes
- Repair the (P669) Driver Mirror Sensor Supply circuit for a short to the (Z911) Ground circuit.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
- Go To 5
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 332
5. CHECK THE (P669) DRIVER MIRROR SENSOR SUPPLY CIRCUIT FOR A SHORT TO THE (P69) DRIVER MIRROR SENSOR
GROUND CIRCUIT
1. Measure the resistance between the (P669) Driver Mirror Sensor Supply circuit and the (P69) Driver Mirror Sensor Ground circuit in the
Driver Door Module C2 connector.
Is the resistance below 10k ohms?
Yes
- Repair the (P669) Driver Mirror Sensor Supply circuit for a short to the (P69) Driver Mirror Sensor Ground circuit.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
- Go To 6
6. CHECK THE (P669) DRIVER MIRROR SENSOR SUPPLY CIRCUIT FOR A SHORT TO THE (C910) DRIVER MIRROR HEATER
RETURN CIRCUIT
1. Measure the resistance between the (P669) Driver Mirror Sensor Supply circuit and the (C910) Driver Mirror Heater Return circuit in the
Driver Outside Rearview Mirror connector.
Is the resistance below 10k ohms?
Yes
- Repair the (P669) Driver Mirror Sensor Supply circuit for a short to the (C910) Driver Mirror Heater Return circuit.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
No
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 333
- Replace the Driver Door Module.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
