B1B77
B1B77-RIGHT SIDE SATELLITE ACCELERATION SENSOR 3 INTERNAL
- When Monitored:
The Occupant Restraint Controller (ORC) continuously communicates with the Right Side Impact Sensor 3 over the sensor signal circuit. The
sensor communication and on board diagnostics are powered by the ORC signal.
- Set Condition:
This code will set, if the ORC and the Right Side Impact Sensor 3 do not establish and maintain valid data communications.
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. See: Restraints and Safety Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Restraints System Pre-Diagnostic Procedure .
1. VERIFY ACTIVE B1B77-RIGHT SIDE SATELLITE ACCELERATION SENSOR 3 INTERNAL
1. Turn the ignition on.
2. With the scan tool, read ORC DTCs.
NOTE: Ensure the battery is fully charged.
Does the scan tool display an active: B1B77-RIGHT SIDE SATELLITE ACCELERATION SENSOR 3 INTERNAL?
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 203
Yes
- Go To 2
No
- Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. . See: Restraints and Safety Systems/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Restraints System Intermittent Condition Test
2. CHECK THE (R22) OR (R24) RIGHT SIDE IMPACT SENSOR 3 SIGNAL AND GROUND CIRCUITS FOR A SHORT TO
BATTERY
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
1. Disconnect the Right Side Impact Sensor 3 connector.
2. Disconnect the ORC connector.
3. Connect the 8443A Load Tool ORC Adaptor to the Occupant Restraint Controller C2 connector.
WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
4. Measure the voltage of the (R22) Right Side Impact Sensor 3 Signal circuit and (R24) Sensor Ground circuit at the Right Side Impact Sensor 3
connector and ground.
Is there any voltage present?
Yes
- Repair the (R22) or (R24) Right Side Impact Sensor 3 circuits for a short to battery.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
No
- Go To 3
3. CHECK THE (R22) RIGHT SIDE IMPACT SENSOR 3 SIGNAL CIRCUIT FOR A SHORT TO GROUND
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
1. Measure the resistance of the (R22) Right Side Impact Sensor 3 Signal circuit between the Right Side Impact Sensor 3 connector and ground.
Is the resistance below 100K Ohms?
Yes
- Repair the (R22) Right Side Impact Sensor 3 Signal circuit for a short to ground.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
No
- Go To 4
4. CHECK THE (R22) AND (R24) RIGHT SIDE IMPACT SENSOR 3 CIRCUITS FOR A SHORT TOGETHER
1. Measure the resistance between the (R22) Right Side Impact Sensor 3 Signal and (R24) Sensor Ground circuits at the Right Side Impact
Sensor 3 connector.
Is the resistance below 100K ohms?
Yes
- Repair the (R22) and (R24) Right Side Impact Sensor 3 circuits shorted together.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
No
- Go To 5
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 204
5. CHECK THE (R24) RIGHT SIDE IMPACT SENSOR 3 GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance of the (R24) Right Side Impact Sensor 3 Ground circuit between the Right Side Impact Sensor 3 connector and the
8443A Load Tool ORC Adaptor.
Is the resistance below 1 ohm?
Yes
- Go To 6
No
- Repair the (R24) Right Side Impact Sensor 3 Ground circuit for an open or high resistance.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
6. CHECK THE (R22) RIGHT SIDE IMPACT SENSOR 3 CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance of the (R22) Right Side Impact Sensor 3 Signal circuit between the Right Side Impact Sensor 3 connector and the
8443A Load Tool ORC Adaptor.
Is the resistance below 1 ohm?
Yes
- Go To 7
No
- Repair the (R22) Right Side Impact Sensor 3 Signal circuit for an open or high resistance.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
7. CHECK OPERATION OF THE RIGHT SIDE IMPACT SENSOR 3
1. Replace the Right Side Impact Sensor 3.
2. Reconnect the vehicle body harness to the impact sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
4. Connect the scan tool to the Data Link Connector - use the most current software available.
5. Use the scan tool and erase the stored codes in all airbag system modules.
6. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
7. Wait one minute, and read active codes and if there are none present read the stored codes.
Did the active Right Side Impact Sensor 3 DTC return?
Yes
- Go To 8
No
- Repair is complete.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
8. REPLACE THE OCCUPANT RESTRAINT CONTROLLER
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
WARNING: If the airbag control module is dropped at any time, it must be replaced. Failure to take the proper precautions could result in
accidental airbag deployment and serious or fatal injury.
Repair
- Replace the Occupant Restraint Controller.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
B1B77-RIGHT SIDE SATELLITE ACCELERATION SENSOR 3 INTERNAL
- When Monitored:
The Occupant Restraint Controller (ORC) continuously communicates with the Right Side Impact Sensor 3 over the sensor signal circuit. The
sensor communication and on board diagnostics are powered by the ORC signal.
- Set Condition:
This code will set, if the ORC and the Right Side Impact Sensor 3 do not establish and maintain valid data communications.
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. See: Restraints and Safety Systems/Testing and
Inspection/Initial Inspection and Diagnostic Overview/Restraints System Pre-Diagnostic Procedure .
1. VERIFY ACTIVE B1B77-RIGHT SIDE SATELLITE ACCELERATION SENSOR 3 INTERNAL
1. Turn the ignition on.
2. With the scan tool, read ORC DTCs.
NOTE: Ensure the battery is fully charged.
Does the scan tool display an active: B1B77-RIGHT SIDE SATELLITE ACCELERATION SENSOR 3 INTERNAL?
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 203
Yes
- Go To 2
No
- Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. . See: Restraints and Safety Systems/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Restraints System Intermittent Condition Test
2. CHECK THE (R22) OR (R24) RIGHT SIDE IMPACT SENSOR 3 SIGNAL AND GROUND CIRCUITS FOR A SHORT TO
BATTERY
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
1. Disconnect the Right Side Impact Sensor 3 connector.
2. Disconnect the ORC connector.
3. Connect the 8443A Load Tool ORC Adaptor to the Occupant Restraint Controller C2 connector.
WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
4. Measure the voltage of the (R22) Right Side Impact Sensor 3 Signal circuit and (R24) Sensor Ground circuit at the Right Side Impact Sensor 3
connector and ground.
Is there any voltage present?
Yes
- Repair the (R22) or (R24) Right Side Impact Sensor 3 circuits for a short to battery.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
No
- Go To 3
3. CHECK THE (R22) RIGHT SIDE IMPACT SENSOR 3 SIGNAL CIRCUIT FOR A SHORT TO GROUND
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
1. Measure the resistance of the (R22) Right Side Impact Sensor 3 Signal circuit between the Right Side Impact Sensor 3 connector and ground.
Is the resistance below 100K Ohms?
Yes
- Repair the (R22) Right Side Impact Sensor 3 Signal circuit for a short to ground.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
No
- Go To 4
4. CHECK THE (R22) AND (R24) RIGHT SIDE IMPACT SENSOR 3 CIRCUITS FOR A SHORT TOGETHER
1. Measure the resistance between the (R22) Right Side Impact Sensor 3 Signal and (R24) Sensor Ground circuits at the Right Side Impact
Sensor 3 connector.
Is the resistance below 100K ohms?
Yes
- Repair the (R22) and (R24) Right Side Impact Sensor 3 circuits shorted together.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
No
- Go To 5
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 204
5. CHECK THE (R24) RIGHT SIDE IMPACT SENSOR 3 GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance of the (R24) Right Side Impact Sensor 3 Ground circuit between the Right Side Impact Sensor 3 connector and the
8443A Load Tool ORC Adaptor.
Is the resistance below 1 ohm?
Yes
- Go To 6
No
- Repair the (R24) Right Side Impact Sensor 3 Ground circuit for an open or high resistance.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
6. CHECK THE (R22) RIGHT SIDE IMPACT SENSOR 3 CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance of the (R22) Right Side Impact Sensor 3 Signal circuit between the Right Side Impact Sensor 3 connector and the
8443A Load Tool ORC Adaptor.
Is the resistance below 1 ohm?
Yes
- Go To 7
No
- Repair the (R22) Right Side Impact Sensor 3 Signal circuit for an open or high resistance.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
7. CHECK OPERATION OF THE RIGHT SIDE IMPACT SENSOR 3
1. Replace the Right Side Impact Sensor 3.
2. Reconnect the vehicle body harness to the impact sensor.
3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
4. Connect the scan tool to the Data Link Connector - use the most current software available.
5. Use the scan tool and erase the stored codes in all airbag system modules.
6. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
7. Wait one minute, and read active codes and if there are none present read the stored codes.
Did the active Right Side Impact Sensor 3 DTC return?
Yes
- Go To 8
No
- Repair is complete.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
8. REPLACE THE OCCUPANT RESTRAINT CONTROLLER
WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these
instructions may result in possible serious or fatal injury.
WARNING: If the airbag control module is dropped at any time, it must be replaced. Failure to take the proper precautions could result in
accidental airbag deployment and serious or fatal injury.
Repair
- Replace the Occupant Restraint Controller.
- Perform the ORC VERIFICATION TEST. See: Verification Tests/Occupant Restraint Controller (ORC) Verification Test.
