B1A41
B1A41-SECURITY TRANSMITTER SENSOR CIRCUIT OPEN
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 45
- When Monitored:
When the VTSS is armed.
- Set Condition:
If the voltage current is below a specified range this DTC will set.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 46
1. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, record and erase DTCs.
3. Turn the ignition off and remove the key from the ignition.
4. Close all doors and arm the VTSS and wait one minute.
5. Disarm the VTSS turn the ignition on and wait one minute.
6. With the scan tool, read DTCs.
Does the scan tool display B1A41-SECURITY TRANSMITTER SENSOR CIRCUIT OPEN?
Yes
- Go To 2
No
- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and
connectors.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
2. CHECK THE (A645) INTRUSION TRANSMITTER SENSOR SIGNAL CIRCUIT VOLTAGE
1. Disconnect the Intrusion Sensor Transmitter connector.
NOTE: Check connectors - Clean/repair as necessary.
2. Turn the ignition on.
3. With the scan tool actuate the Intrusion Sensor Transmitter.
4. Measure the voltage between (A645) Intrusion Sensor Signal circuit and (G945) Sensor Ground circuit.
Is the voltage above 10.0 volts
Yes
- Go To 3
No
- Go To 4
3. CHECK THE INTRUSION SENSOR TRANSMITTER
1. Turn the ignition off.
2. Install a known good Intrusion Sensor Transmitter.
3. Turn the ignition on.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 47
4. With the scan tool erase DTCs.
5. Turn the ignition off and remove the key from the ignition.
6. Close all doors and arm the VTSS and wait one minute.
7. Disarm the VTSS turn the ignition on and wait one minute.
8. With the scan tool, read DTCs.
Does the scan tool display B1A41-SECURITY TRANSMITTER SENSOR CIRCUIT OPEN?
Yes
- Replace the Intrusion Transceiver Module.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
No
- Replace the original Intrusion Sensor Transmitter.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
4. CHECK THE (A645) INTRUSION TRANSMITTER SENSOR SIGNAL WIRE
1. Turn the ignition off.
2. Disconnect the Intrusion Transceiver Module connector.
3. Measure the resistance of the (A645) Intrusion Transmitter Sensor Signal circuit between the Intrusion Sensor Transmitter connector and the
Intrusion Transceiver Module connector.
Is the resistance below 5.0 ohms?
Yes
- Repair the (A645) Intrusion Transmitter Sensor Signal circuit for an open.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
No
- Go To 5
5. CHECK THE (G945) SENSOR GROUND WIRE FOR AN OPEN
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 48
1. Ensure Ignition off.
2. Measure the resistance of the (G945) Sensor Ground circuit from the Intrusion Sensor Transmitter connector to the Intrusion Transceiver
Module connector.
Is the resistance below 5.0 ohms?
Yes
- Replace the Intrusion Transceiver Module.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
No
- Repair the (G945) Sensor Ground circuit for an open.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
B1A41-SECURITY TRANSMITTER SENSOR CIRCUIT OPEN
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 45
- When Monitored:
When the VTSS is armed.
- Set Condition:
If the voltage current is below a specified range this DTC will set.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 46
1. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. With the scan tool, record and erase DTCs.
3. Turn the ignition off and remove the key from the ignition.
4. Close all doors and arm the VTSS and wait one minute.
5. Disarm the VTSS turn the ignition on and wait one minute.
6. With the scan tool, read DTCs.
Does the scan tool display B1A41-SECURITY TRANSMITTER SENSOR CIRCUIT OPEN?
Yes
- Go To 2
No
- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and
connectors.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
2. CHECK THE (A645) INTRUSION TRANSMITTER SENSOR SIGNAL CIRCUIT VOLTAGE
1. Disconnect the Intrusion Sensor Transmitter connector.
NOTE: Check connectors - Clean/repair as necessary.
2. Turn the ignition on.
3. With the scan tool actuate the Intrusion Sensor Transmitter.
4. Measure the voltage between (A645) Intrusion Sensor Signal circuit and (G945) Sensor Ground circuit.
Is the voltage above 10.0 volts
Yes
- Go To 3
No
- Go To 4
3. CHECK THE INTRUSION SENSOR TRANSMITTER
1. Turn the ignition off.
2. Install a known good Intrusion Sensor Transmitter.
3. Turn the ignition on.
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 47
4. With the scan tool erase DTCs.
5. Turn the ignition off and remove the key from the ignition.
6. Close all doors and arm the VTSS and wait one minute.
7. Disarm the VTSS turn the ignition on and wait one minute.
8. With the scan tool, read DTCs.
Does the scan tool display B1A41-SECURITY TRANSMITTER SENSOR CIRCUIT OPEN?
Yes
- Replace the Intrusion Transceiver Module.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
No
- Replace the original Intrusion Sensor Transmitter.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
4. CHECK THE (A645) INTRUSION TRANSMITTER SENSOR SIGNAL WIRE
1. Turn the ignition off.
2. Disconnect the Intrusion Transceiver Module connector.
3. Measure the resistance of the (A645) Intrusion Transmitter Sensor Signal circuit between the Intrusion Sensor Transmitter connector and the
Intrusion Transceiver Module connector.
Is the resistance below 5.0 ohms?
Yes
- Repair the (A645) Intrusion Transmitter Sensor Signal circuit for an open.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
No
- Go To 5
5. CHECK THE (G945) SENSOR GROUND WIRE FOR AN OPEN
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 48
1. Ensure Ignition off.
2. Measure the resistance of the (G945) Sensor Ground circuit from the Intrusion Sensor Transmitter connector to the Intrusion Transceiver
Module connector.
Is the resistance below 5.0 ohms?
Yes
- Replace the Intrusion Transceiver Module.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
No
- Repair the (G945) Sensor Ground circuit for an open.
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test
