B1A6B
B1A6B STEERING COLUMN LOCK MODULE NOT INITIALIZED
- When Monitored:
Continuously.
- Set Condition:
The Wireless Ignition Node detects that the Steering Column Lock Module has not initialized. The WIN has been enabled with the Steering
Wheel Lock Module but did not personalized
1. STEERING COLUMN LOCK MODULE
1. With the scan tool, record and erase WIN DTCs.
2. Remove and insert the key from the ignition switch several times then leave the key in the run position.
3. With the scan tool, read the active DTCs.
Does the scan tool display: B1A6B STEERING COLUMN LOCK MODULE NOT INITIALIZED?
Yes
- Go To 2
No
- Perform the WIRELESS IGNITION NODE (WIN) INTERMITTENT TEST.. See: Verification Tests/Vehicle Theft Security Verification
Tests/Wireless Ignition Node (WIN) Verification Test
2. INITIALIZE STEERING COLUMN LOCK MODULE
1. With the scan tool, erase the DTCs in the WIN.
2. With the scan tool, perform the Steering Wheel Lock Module (ELV) Replaced routine.
3. Turn the Ignition off, wait 15 seconds then turn the ignition back on.
4. Remove and insert the key from the ignition switch several times then leave the key in the run position.
5. With the scan tool, read the DTCs.
Does the scan tool display: B1A6B STEERING COLUMN LOCK MODULE NOT INITIALIZED?
Yes
- Replace the Steering Column Lock Module. The Wireless Ignition Node (WIN) must also be replaced along with the Steering Column
Lock Module (ELV). When replacing the WIN and the Steering Column Lock Module (ELV), the WIN MUST be programmed
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 18
BEFORE the Steering Column Lock Module (ELV) is programmed..
- Replace and program the Wireless Ignition Node (WIN). See: Powertrain Management/Ignition System/Sensors and Switches - Ignition
System/Ignition Switch/Service and Repair/Wireless Ignition Node Receiver - Removal.
- Replace and program the Steering Column Lock Module (ELV). See: Steering and Suspension/Steering/Steering Column/Steering Column
Lock/Service and Repair/Shaft Lock Module - Removal.
- Perform the WIN VERIFICATION TEST. See: Verification Tests/Vehicle Theft Security Verification Tests/Wireless Ignition Node (WIN)
Verification Test.
No
- Test complete
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
B1A6B STEERING COLUMN LOCK MODULE NOT INITIALIZED
- When Monitored:
Continuously.
- Set Condition:
The Wireless Ignition Node detects that the Steering Column Lock Module has not initialized. The WIN has been enabled with the Steering
Wheel Lock Module but did not personalized
1. STEERING COLUMN LOCK MODULE
1. With the scan tool, record and erase WIN DTCs.
2. Remove and insert the key from the ignition switch several times then leave the key in the run position.
3. With the scan tool, read the active DTCs.
Does the scan tool display: B1A6B STEERING COLUMN LOCK MODULE NOT INITIALIZED?
Yes
- Go To 2
No
- Perform the WIRELESS IGNITION NODE (WIN) INTERMITTENT TEST.. See: Verification Tests/Vehicle Theft Security Verification
Tests/Wireless Ignition Node (WIN) Verification Test
2. INITIALIZE STEERING COLUMN LOCK MODULE
1. With the scan tool, erase the DTCs in the WIN.
2. With the scan tool, perform the Steering Wheel Lock Module (ELV) Replaced routine.
3. Turn the Ignition off, wait 15 seconds then turn the ignition back on.
4. Remove and insert the key from the ignition switch several times then leave the key in the run position.
5. With the scan tool, read the DTCs.
Does the scan tool display: B1A6B STEERING COLUMN LOCK MODULE NOT INITIALIZED?
Yes
- Replace the Steering Column Lock Module. The Wireless Ignition Node (WIN) must also be replaced along with the Steering Column
Lock Module (ELV). When replacing the WIN and the Steering Column Lock Module (ELV), the WIN MUST be programmed
2010 Jeep Truck Grand Cherokee SRT-8 V8-6.1L Page 18
BEFORE the Steering Column Lock Module (ELV) is programmed..
- Replace and program the Wireless Ignition Node (WIN). See: Powertrain Management/Ignition System/Sensors and Switches - Ignition
System/Ignition Switch/Service and Repair/Wireless Ignition Node Receiver - Removal.
- Replace and program the Steering Column Lock Module (ELV). See: Steering and Suspension/Steering/Steering Column/Steering Column
Lock/Service and Repair/Shaft Lock Module - Removal.
- Perform the WIN VERIFICATION TEST. See: Verification Tests/Vehicle Theft Security Verification Tests/Wireless Ignition Node (WIN)
Verification Test.
No
- Test complete
- Perform the BODY VERIFICATION TEST. See: Verification Tests/Body Verification Test.
