Jeep Truck Grand Cherokee 4WD V85.7L Technical Service Bulletin #K05
Recall Rear Suspension Track Bar Replacement
April 2010
Dealer Service Instructions for:
Safety Recall K05
Rear Suspension Track Bar
Models
2010 (WK) Jeep(R) Grand Cherokee
(XK) Jeep(R) Commander
NOTE:
Date: 1004062010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 89
This recall applies only to the above vehicles built from December 9, 2009 through December 17, 2009 (MDH 120905 through
121709).
IMPORTANT:
Many of the vehicles within the above build period have already been inspected or repaired and, therefore, have been excluded from
this recall.
IMPORTANT:
Some of the involved vehicles may be in dealer new vehicle inventory. Federal law requires you to complete this recall service on
these vehicles before retail delivery. Dealers should also consider this requirement to apply to used vehicle inventory and should
perform this recall on vehicles in for service. Involved vehicles can be determined by using the VIP inquiry process.
Subject
The rear suspension track bar bushing hoops on about 3,400 of the above vehicles may have been incorrectly manufactured and could
fail. A failed track bar could reduce vehicle stability and cause a crash without warning.
Repair
The track bar must be removed from the vehicle and inspected. Track bars found with improperly welded bushing hoop(s) must be
replaced.2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 90
Parts Information
Due to the small number of involved vehicles expected to require a track bar, no parts will be distributed initially. A track bar should be
ordered only after inspection determines that replacement is required. Very few vehicles are expected to require a track bar replacement.
Special Tools
No special tools are required to perform this recall.
Completion Reporting and Reimbursement
Claims for vehicles that have been serviced must be submitted on the
DealerCONNECT Claim Entry Screen located on the Service tab. Claims
submitted will be used by Chrysler to record recall service completions and provide dealer payments.2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 91
Use one of the labor operation numbers and time allowances shown.
NOTE:
See the Warranty Administration Manual, Recall Claim Processing Section, for complete recall claim processing instructions.
Dealer Notification
To view this notification on DealerCONNECT, select "Global Recall System" on the Service tab, then click on the description of this
notification.
Owner Notification and Service Scheduling2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 92
All involved vehicle owners known to Chrysler are being notified of the service requirement by first class mail. They are requested to
schedule appointments for this service with their dealers. A generic copy of the owner letter is included.
Enclosed with each owner letter is an Owner Notification postcard to allow owners to update our records if applicable.
Vehicle Lists, Global Recall System, VIP and Dealer Follow Up
All involved vehicles have been entered into the DealerCONNECT Global Recall System (GRS) and Vehicle Information Plus (VIP) for
dealer inquiry as needed.
GRS provides involved dealers with an updated VIN list of their incomplete vehicles. The owner's name, address and phone number are
listed if known. Completed vehicles are removed from GRS within several days of repair claim submission.
To use this system, click on the "Service" tab and then click on "Global Recall System." Your dealer's VIN list for each recall displayed
can be sorted by: those vehicles that were unsold at recall launch, those with a phone number, city, zip code, or VIN sequence.
Dealers must perform this repair on all unsold vehicles before retail delivery. Dealers should also use the VIN list to follow up with all
owners to schedule appointments for this repair.
Recall VIN lists may contain confidential, restricted owner name and address information that was obtained from the Department of Motor
Vehicles of various states. Use of this information is permitted for this recall only and is strictly prohibited from all other use.
Additional Information
If you have any questions or need assistance in completing this action, please contact your Service and Parts District Manager.
Customer Services Field Operations
Chrysler Group LLC
Service Procedure
1. Remove the rear suspension track bar using the following procedure:
a. Raise the vehicle on an appropriate hoist.
b. Remove the right side (axle side) track bar retaining bolt (Figure 1).2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 93
c. Remove the left side (body side) track bar retaining bolt (Figure 2).
CAUTION:
The left rear coil spring may have to be slightly compressed to remove the left side track bar retaining bolt. Use extreme care not to
nick or scratch the coil spring's protective coating.
d. Carefully remove the track bar from the vehicle.2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 94
2. Inspect both track bar bushing hoops (Figure 3):
> If the part line (seam) on both bushing hoops are at or near the center line of the track bar (+/ 1/4 inch (6 mm) from center), the
track bar does not require replacement (Figure 3).
> If the part line (seam) on either of the bushing hoops is not within +/ 1/4 inch (6 mm) from the center line of the track bar, replace
the track bar (Figure 3).
3. Place the track bar into position on the vehicle.
NOTE:
The track bar is symmetrical and can be installed in either direction.
4. Loosely install the left and right track bar retaining bolts and nuts. DO NOT TIGHTEN THE TRACK BAR RETAINING BOLTS AT
THIS TIME.
5. Lower the vehicle from the hoist.
6. Jounce the rear suspension several times to settle the suspension.
7. Using a mechanic's creeper, slide under the vehicle and tighten both track bar retaining bolts to 140 ft. lbs. (190 N.m).2010 Jeep Truck Grand Cherokee 4WD V85.7L
Recall Rear Suspension Track Bar Replacement
April 2010
Dealer Service Instructions for:
Safety Recall K05
Rear Suspension Track Bar
Models
2010 (WK) Jeep(R) Grand Cherokee
(XK) Jeep(R) Commander
NOTE:
Date: 1004062010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 89
This recall applies only to the above vehicles built from December 9, 2009 through December 17, 2009 (MDH 120905 through
121709).
IMPORTANT:
Many of the vehicles within the above build period have already been inspected or repaired and, therefore, have been excluded from
this recall.
IMPORTANT:
Some of the involved vehicles may be in dealer new vehicle inventory. Federal law requires you to complete this recall service on
these vehicles before retail delivery. Dealers should also consider this requirement to apply to used vehicle inventory and should
perform this recall on vehicles in for service. Involved vehicles can be determined by using the VIP inquiry process.
Subject
The rear suspension track bar bushing hoops on about 3,400 of the above vehicles may have been incorrectly manufactured and could
fail. A failed track bar could reduce vehicle stability and cause a crash without warning.
Repair
The track bar must be removed from the vehicle and inspected. Track bars found with improperly welded bushing hoop(s) must be
replaced.2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 90
Parts Information
Due to the small number of involved vehicles expected to require a track bar, no parts will be distributed initially. A track bar should be
ordered only after inspection determines that replacement is required. Very few vehicles are expected to require a track bar replacement.
Special Tools
No special tools are required to perform this recall.
Completion Reporting and Reimbursement
Claims for vehicles that have been serviced must be submitted on the
DealerCONNECT Claim Entry Screen located on the Service tab. Claims
submitted will be used by Chrysler to record recall service completions and provide dealer payments.2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 91
Use one of the labor operation numbers and time allowances shown.
NOTE:
See the Warranty Administration Manual, Recall Claim Processing Section, for complete recall claim processing instructions.
Dealer Notification
To view this notification on DealerCONNECT, select "Global Recall System" on the Service tab, then click on the description of this
notification.
Owner Notification and Service Scheduling2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 92
All involved vehicle owners known to Chrysler are being notified of the service requirement by first class mail. They are requested to
schedule appointments for this service with their dealers. A generic copy of the owner letter is included.
Enclosed with each owner letter is an Owner Notification postcard to allow owners to update our records if applicable.
Vehicle Lists, Global Recall System, VIP and Dealer Follow Up
All involved vehicles have been entered into the DealerCONNECT Global Recall System (GRS) and Vehicle Information Plus (VIP) for
dealer inquiry as needed.
GRS provides involved dealers with an updated VIN list of their incomplete vehicles. The owner's name, address and phone number are
listed if known. Completed vehicles are removed from GRS within several days of repair claim submission.
To use this system, click on the "Service" tab and then click on "Global Recall System." Your dealer's VIN list for each recall displayed
can be sorted by: those vehicles that were unsold at recall launch, those with a phone number, city, zip code, or VIN sequence.
Dealers must perform this repair on all unsold vehicles before retail delivery. Dealers should also use the VIN list to follow up with all
owners to schedule appointments for this repair.
Recall VIN lists may contain confidential, restricted owner name and address information that was obtained from the Department of Motor
Vehicles of various states. Use of this information is permitted for this recall only and is strictly prohibited from all other use.
Additional Information
If you have any questions or need assistance in completing this action, please contact your Service and Parts District Manager.
Customer Services Field Operations
Chrysler Group LLC
Service Procedure
1. Remove the rear suspension track bar using the following procedure:
a. Raise the vehicle on an appropriate hoist.
b. Remove the right side (axle side) track bar retaining bolt (Figure 1).2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 93
c. Remove the left side (body side) track bar retaining bolt (Figure 2).
CAUTION:
The left rear coil spring may have to be slightly compressed to remove the left side track bar retaining bolt. Use extreme care not to
nick or scratch the coil spring's protective coating.
d. Carefully remove the track bar from the vehicle.2010 Jeep Truck Grand Cherokee 4WD V85.7L
Page 94
2. Inspect both track bar bushing hoops (Figure 3):
> If the part line (seam) on both bushing hoops are at or near the center line of the track bar (+/ 1/4 inch (6 mm) from center), the
track bar does not require replacement (Figure 3).
> If the part line (seam) on either of the bushing hoops is not within +/ 1/4 inch (6 mm) from the center line of the track bar, replace
the track bar (Figure 3).
3. Place the track bar into position on the vehicle.
NOTE:
The track bar is symmetrical and can be installed in either direction.
4. Loosely install the left and right track bar retaining bolts and nuts. DO NOT TIGHTEN THE TRACK BAR RETAINING BOLTS AT
THIS TIME.
5. Lower the vehicle from the hoist.
6. Jounce the rear suspension several times to settle the suspension.
7. Using a mechanic's creeper, slide under the vehicle and tighten both track bar retaining bolts to 140 ft. lbs. (190 N.m).2010 Jeep Truck Grand Cherokee 4WD V85.7L
