Technical Service Bulletin #3100712
Body/Frame Welded Sheet Metal Repairs And Replacements
NUMBER: 3100712
GROUP: Collision Bulletin
DATE: August 14, 2012
SUBJECT:
Welded Sheet Metal Repairs and Replacements
OVERVIEW:
This bulletin discuss the recommended weld processes when replacing a panel that has been welded to the vehicle.
DISCUSSION:
Date: 1208142010 Jeep Truck Grand Cherokee 4WD V63.7L
Page 45
Regardless of the cause of vehicular damage, the repairers moral obligation is to repair the vehicle to the original design intent relative to
safety, NVH, comfort, durability, and corrosion protection by duplicating the original construction as closely as possible by
following all manufacturers guidelines. With the increasing use of advanced high strength steels in body construction, and their
susceptibility to degraded material properties from welding heat, the approved process for installation of replacement panels has
changed.
Chrysler has previously approved the use of "weld bonding", where squeeze type resistance spot welding (STRSW) is combined with an
approved structural adhesive, as one of the acceptable methods to install welded panels while maintaining the original appearance and
corrosion protection.
High quality and capable STRSW equipment, which was a rare shop tool in the collision repair industry, has now become the norm and
with this, it is now important to state that weld bonding of replacement panels is the recommended installation method to utilize when
repairing Chrysler, Dodge, Fiat, Jeep, or Ram vehicles.
GAS METAL ARC WELDING (GMAW or MIG) SHOULD ONLY BE USED IN THE
FOLLOWING SPECIAL CIRCUMSTANCES:
^ Proper weld access cannot be attained utilizing STRSW equipment with any of the available accessory arms.
^ Utilize 68 mm ring fillet welds for exterior panels and 810 mm for all others.
^ Adhesives need to be kept 25 mm from a ring fillet weld due to their flammability.
^ A Chrysler publication explicitly calls out fusion welding as the proper repair method.
^ The original attachment was GMAW.
ALL OF THE FOLLOWING GUIDELINES MUST BE ADHERED TO:
^ DO NOT use heat to straighten sheet metal unless the panel will be replaced.
^
If weldon pulling studs are used, their use must be minimal and the backside of the repaired panel must also be repaired to restore
the original corrosion protection.
CHARACTERISTIC OF ACCEPTABLE STRSW EQUIPMENT:
^
^
^
^
^
Must utilize 220 volt (or greater), threephase power supply.
Must utilize inverter technology
Must have the capability to provide a minimum of 10,000 amps of output.
Must have the capability to provide 600 pounds of tip force (267 daN) with the longest arms
Should utilize "smart" technology which helps eliminate errors in equipment setup.
STRSW EQUIPMENT MEETING THE CRITERIA INCLUDES:
^
^
^
^
^
^
^
^
^
CarOLiner CTR12000
Cebotech Tecna SmartPlus 3664+
Elektron Multispot MI100 Control
Pro Spot i5
ONLY Lord Fusor # 112B or 3M # 08116 have been approved by Chrysler for weld bonding. These materials provide corrosion
protection in the vulnerable weld zone. Joint sealers should be applied after welding is complete and appropriate primers have been
applied (if needed).
Only remove ecoat from the new panel at the weldbond mating location.
Minimize removal of galvanize/galvanneal coating.
Solvent wipe with suitable product before application of adhesive.
Initial application of adhesive should be spread from the bare metal onto the ecoat to provide a continuous corrosion barrier.
THE REPLACEMENT STRSW WELDS SHOULD DUPLICATE THE ORIGINAL WELDS
IN:
^
^
^
Size
Quantity
Location
NOTE:
replacement welds should be within inch of the original location while trying to avoid placing new welds over old welds. Where
replacing only the exterior panel in a 3T situation, the new weld should be placed about 3/8inch away to avoid shunting and
reestablish a 3T weld.2010 Jeep Truck Grand Cherokee 4WD V63.7L
^
^
^
Page 46
Never use "weldthru" primer.
Completing all welded panel replacements requires applying a coating of creeping rust inhibitive material in all areas where any welds
were made, even where weldbonded.
Replacement panels must be installed as provided, and utilizing the methods described in this bulletin, unless additional guidelines
are made in another Chrysler Collision Repair Bulletin, Chrysler Body Repair Manual, or other Chrysler approved publication.
Failure to follow these repair guidelines will result in a vehicle which may not duplicate the original design intent in terms of function,
safety, and durability.
POLICY:
Information Only
Disclaimer:
This bulletin is supplied as technical information only and is not an authorization for repair.
Body/Frame Welded Sheet Metal Repairs And Replacements
NUMBER: 3100712
GROUP: Collision Bulletin
DATE: August 14, 2012
SUBJECT:
Welded Sheet Metal Repairs and Replacements
OVERVIEW:
This bulletin discuss the recommended weld processes when replacing a panel that has been welded to the vehicle.
DISCUSSION:
Date: 1208142010 Jeep Truck Grand Cherokee 4WD V63.7L
Page 45
Regardless of the cause of vehicular damage, the repairers moral obligation is to repair the vehicle to the original design intent relative to
safety, NVH, comfort, durability, and corrosion protection by duplicating the original construction as closely as possible by
following all manufacturers guidelines. With the increasing use of advanced high strength steels in body construction, and their
susceptibility to degraded material properties from welding heat, the approved process for installation of replacement panels has
changed.
Chrysler has previously approved the use of "weld bonding", where squeeze type resistance spot welding (STRSW) is combined with an
approved structural adhesive, as one of the acceptable methods to install welded panels while maintaining the original appearance and
corrosion protection.
High quality and capable STRSW equipment, which was a rare shop tool in the collision repair industry, has now become the norm and
with this, it is now important to state that weld bonding of replacement panels is the recommended installation method to utilize when
repairing Chrysler, Dodge, Fiat, Jeep, or Ram vehicles.
GAS METAL ARC WELDING (GMAW or MIG) SHOULD ONLY BE USED IN THE
FOLLOWING SPECIAL CIRCUMSTANCES:
^ Proper weld access cannot be attained utilizing STRSW equipment with any of the available accessory arms.
^ Utilize 68 mm ring fillet welds for exterior panels and 810 mm for all others.
^ Adhesives need to be kept 25 mm from a ring fillet weld due to their flammability.
^ A Chrysler publication explicitly calls out fusion welding as the proper repair method.
^ The original attachment was GMAW.
ALL OF THE FOLLOWING GUIDELINES MUST BE ADHERED TO:
^ DO NOT use heat to straighten sheet metal unless the panel will be replaced.
^
If weldon pulling studs are used, their use must be minimal and the backside of the repaired panel must also be repaired to restore
the original corrosion protection.
CHARACTERISTIC OF ACCEPTABLE STRSW EQUIPMENT:
^
^
^
^
^
Must utilize 220 volt (or greater), threephase power supply.
Must utilize inverter technology
Must have the capability to provide a minimum of 10,000 amps of output.
Must have the capability to provide 600 pounds of tip force (267 daN) with the longest arms
Should utilize "smart" technology which helps eliminate errors in equipment setup.
STRSW EQUIPMENT MEETING THE CRITERIA INCLUDES:
^
^
^
^
^
^
^
^
^
CarOLiner CTR12000
Cebotech Tecna SmartPlus 3664+
Elektron Multispot MI100 Control
Pro Spot i5
ONLY Lord Fusor # 112B or 3M # 08116 have been approved by Chrysler for weld bonding. These materials provide corrosion
protection in the vulnerable weld zone. Joint sealers should be applied after welding is complete and appropriate primers have been
applied (if needed).
Only remove ecoat from the new panel at the weldbond mating location.
Minimize removal of galvanize/galvanneal coating.
Solvent wipe with suitable product before application of adhesive.
Initial application of adhesive should be spread from the bare metal onto the ecoat to provide a continuous corrosion barrier.
THE REPLACEMENT STRSW WELDS SHOULD DUPLICATE THE ORIGINAL WELDS
IN:
^
^
^
Size
Quantity
Location
NOTE:
replacement welds should be within inch of the original location while trying to avoid placing new welds over old welds. Where
replacing only the exterior panel in a 3T situation, the new weld should be placed about 3/8inch away to avoid shunting and
reestablish a 3T weld.2010 Jeep Truck Grand Cherokee 4WD V63.7L
^
^
^
Page 46
Never use "weldthru" primer.
Completing all welded panel replacements requires applying a coating of creeping rust inhibitive material in all areas where any welds
were made, even where weldbonded.
Replacement panels must be installed as provided, and utilizing the methods described in this bulletin, unless additional guidelines
are made in another Chrysler Collision Repair Bulletin, Chrysler Body Repair Manual, or other Chrysler approved publication.
Failure to follow these repair guidelines will result in a vehicle which may not duplicate the original design intent in terms of function,
safety, and durability.
POLICY:
Information Only
Disclaimer:
This bulletin is supplied as technical information only and is not an authorization for repair.
